Silverfast hdr software1/29/2024 One of the most annoying aspects of digital camera scanning is the need to remove dust. Placing the film directly on the light table can lead to newton-rings, and will exacerbate any small variances in light.įlatness is crucial to getting edge-to-edge sharpness across the entire frame - the depth of field of macro lenses is incredibly sensitive, so look for a film holder/carrier that has built-in mechanisms to keep the film flat. Use a film carrier that elevates the film off the surface of your light pad. The important considerations are 1) film flatness, 2) speed, 3) limiting contact with film. Now that you have a lens, light source and stand, you need a way to safely elevate and transport your film for each shot. The disadvantage is that this method is not as flexible for working with different film formats, or switching between lenses. The advantage of this setup is that it keeps everything in plane and stray light out. The sturdiest way to use a tripod is to invert the center column and shoot straight down.Īn alternative to copy-stands and tripods is using a bellows or digitization adaptor ( see this example). In a pinch, you can use a traditional tripod. They are significantly easier to adjust than a tripod, are more stable, and more ergonomic to use while sitting at your desk. You’ll want to look for a solution that is easy to finely adjust, as well as being sturdy enough to remain fixed in place for an entire session of film digitization.Ī sturdy copy-stand with an adjustable height is the ideal solution. You’ll need a way to keep your camera stationary and in plane with your film. It’s generally recommended to use a daylight balanced light source with a temperature of 5000°K or 5500°K - you certainly don’t want your light to be any warmer than this! If you are using a flash as a light source, special care will need to be taken to ensure even diffused light. If you are using a pixelated source (like an iPad) you’ll need to raise the film higher off the surface or use a diffuser (like opalized glass) to even out the light. Look for an even lighting source - high-quality light pads made specifically for camera scanning should provide even illumination. If the manufacturer does not list the CRI, it is a warning sign that it is not a good light source for DSLR film scanning. Look for a light with a high CRI (Color Rendering Index) of at least 90+. Poor light sources can also cause uneven lighting in your scan, which not only throws off the tonal balance, but will create uneven color reproduction. Poor light sources will not be able to bring out the rich, natural colors in your negative. The colors from your DSLR scan will only be as good as the light source that you use. They allow you to keep the lens further from the negative, thus reducing the likelihood of lens reflections. Longer focal lengths are preferable to shorter focal lengths. Adaptors can also throw off lens corrections that are performed later in software. Every adaptor or tube adds to the likelihood of light variances that will throw off the color (which may not be visible during capture, but will be amplified by the conversion). Use a “native” lens if possible (and avoid adaptors and tubes). Not only will a modern macro lens produce sharper results, but the newer AR coatings decrease the chance of lens flare during capture (lens flare can lead to strange colors and casts). Not only will a good macro lens produce great edge-to-edge sharpness of your negative scan, but it will also prevent some of the most common issues with DSLR scanning, like orange blotches resulting from lens flare during capture. The lens is an incredibly important part of the DSLR/Mirrorless scanning process. Having the right equipment plays a key role in getting great results with digital camera scans! There are 4 basics components to a good DSLR film scanning setup… While DSLR (or Mirrorless) film scanning holds many promising results – like RAW capture, faster capture times, and sharpness that rivals $10,000+ drum scanners – there are many potential stumbling blocks along the way that could prevent you from getting the results you want from your film negatives. Scanning your film negatives with a digital camera can be an incredibly rewarding – or incredibly frustrating – process, largely depending on your setup and know-how. The input must be good for the output to be good. For Negative Lab Pro to work properly, it’s important that you have good, evenly-lit, properly-exposed scans of your negative film.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |